DIY Midcentury Plant Stand

May 22 2017 |

This is a sponsored post written by me on behalf of Miracle-Gro for IZEA. All opinions are 100% mine.

DIY Midcentury Modern Plant Stand

DIY Midcentury Modern Plant Stand

DIY Midcentury Modern Plant Stand

This project has been on our to-do list forever. You know those projects? The ones that you mean to do but you just keep putting off for one reason or another? I think I was scared that it would be too hard so I kept procrastinating. But my super handy husband helped me figure out a way to make this DIY midcentury plant stand that’s so easy even a novice woodworker can tackle it. And now I kind of want to make them for all of our indoor pots. What can I say? I’ve always been into too much of a good thing.

Materials

  • 1″ dowel
  • 3/4″ dowel
  • 1/4″ wood pegs
  • wood glue
  • clamp
  • drill with 3/4″ bit and 1/4″ bit
  • miter saw
  • table saw

Make Time: 30 Minutes (Plus Drying Time)

DIY midcentury modern plant stand

Step 1: Cut your dowels to the appropriate length. The 1″ dowel will create the vertical bars, so cut four of them as tall as you would like. The ¾” dowel will create the crossbars underneath your pot. Cut two of these, each ½” longer than the width of your pot.

Step 2: Decide where you would like your pot to sit on the vertical bars. Measure and mark the distance from the end of each bar and drill a ¾” hole on each section of vertical bar. This hole should only be drilled ⅛” into the dowel. Within this shallow hole, drill a ¼” hole another ¼” into the dowel.

Step 3: Use a ¼” drill bit to drill a hole on either end of each crossbar.

Step 4: Measure and mark the center point on both crossbars. Set your table saw to 3/8″ height. Using a table saw to notch out ¾” of wood (⅜” on either side of your center mark).

Step 5: Apply a dab of wood glue to the holes in two vertical bars. Also apply wood glue to the holes on the ends of one crossbar and insert pegs into these holes. Then insert the crossbar into the holes in the two vertical bars, ensuring that the notch in the crossbar is oriented in the right direction.

Step 6: Repeat step 5 with the remaining pieces. Make sure the notch in this crossbar corresponds to the other crossbar so that they will fit together.

Step 7: Place a dab of wood glue into one of the crossbar notches and fit them together.

Step 8: Place a clamp on the notches in the crossbars until the wood glue dries.

After you’ve got your plant stand constructed, pot your plant! We used Miracle-Gro Expand N’ Gro, which we recently used to repot all of our houseplants . You can use it outdoors too but I particularly love it for potting houseplants because it’s so light. You can have it delivered via Amazon (my answer to everything), and it will come straight to your door. Most other soils won’t deliver because they’re too heavy, but Expand n’ Gro is a special lighter formula. You add water, stir, and it expands to 3x its volume. It also holds a nice amount of water in the soil so plants stay hydrated and healthy. Love this stuff!

DIY Midcentury Modern Plant Stand

DIY Midcentury Modern Plant Stand

DIY Midcentury Modern Plant Stand

And our new plant stand is just what I was envisioning. I always feel so accomplished after a woodworking project – at the start they seem intimidating but broken down step by step, they’re totally achievable. Hope you try this one out! xoxo

DIY Midcentury Modern Plant Stand

DIY Midcentury Modern Plant Stand

Visit Sponsors Site

8 thoughts on “DIY Midcentury Plant Stand”

  1. Thank you so much for this post! I’ve been wanting a mid century modern desk top planter! What size pot did you use?

  2. Love this!! I’ve been looking for some simple DIY plant stands for our new apartment and this looks perfect!! Thanks for sharing. 🙂

Leave a Reply to Horn Beads Cancel reply

Keep the conversation going! Your email address will not be published.

*